Search found 738 matches
- Wed May 21, 2014 12:14 pm
- Forum: Software Support
- Topic: resistance drift with KICKR?
- Replies: 11
- Views: 25254
Re: resistance drift with KICKR?
1) What ANT+ stick are you using? I used to have stick that I had to constantly plug/unplug. Replaced it with ANT USB-m from Digikey, Suunto Movestick mini. When the glitch happens all the data still comes through (KICKR, HR and cadence sensors) it's just that the resistance doesn't change. Do you ...
- Wed May 21, 2014 12:01 pm
- Forum: Software Support
- Topic: resistance drift with KICKR?
- Replies: 11
- Views: 25254
Re: resistance drift with KICKR?
I've since had this happen a few more times. As far as I can tell, what's happening is that the KICKR is resetting to the default resistance and no longer following the input from v_ride. Unplugging the ant stick and plugging it back in seems to resolve the issue. This happens independently of drop...
- Mon May 05, 2014 6:55 pm
- Forum: FAQ (Frequently Asked Questions)
- Topic: KICKR FAQ, SIGNAL DROPS
- Replies: 14
- Views: 69797
Re: BETTER SUPPORT AND KICKR FAQ
Out of hundreds of KICKR's customers very few had complained knocking on a wood myselfrwajtb wrote:I guess I've been lucky in that I haven't even had one 'drop' with ANT+ running the VR software (knock on wood?)
- Sat May 03, 2014 6:33 pm
- Forum: FAQ (Frequently Asked Questions)
- Topic: KICKR FAQ, SIGNAL DROPS
- Replies: 14
- Views: 69797
KICKR FAQ, SIGNAL DROPS
I can do live support over Skype/Teamviewer combination. Will be much faster than exchanging posts. My Skype_ID is poukhov_kostya. For faster replies try to use email. Due to various reasons I am not browsing forums nearly as often as I am reading my email Special note for KICKR users in regards to ...
- Sat May 03, 2014 6:27 pm
- Forum: Software Support
- Topic: VR SW Control of Kickr - resistance not changing with Grade
- Replies: 2
- Views: 6612
Re: VR SW Control of Kickr - resistance not changing with Gr
Do the following experiment: 1) Clear all your ANT+ setting, take away your bike with Vector pedals and HR sensors. 2) Make sure KICKR is powered and "Learn"/"Save" ANT+ configuration. You do not have to have KICKR spinning to have it detected. 3) At this point you should only ha...
- Mon Apr 28, 2014 8:25 pm
- Forum: Software Support
- Topic: Version 1.2.0.74
- Replies: 2
- Views: 6002
Re: Version 1.2.0.74
Sen email to kostya@veloreality.com and I'll take you it from there. You can also attach TCX file. As for display changes that is what majority customers asked me to do. They did not quite get progressive zoom display and I was advised to just show nearest 1000 meters. You have whole profile on your...
- Wed Apr 09, 2014 6:24 am
- Forum: Videos General Discussion
- Topic: TACX Frustration!
- Replies: 1
- Views: 7175
Re: TACX Frustration!
LOL. Thanks for kind words.
- Sun Mar 30, 2014 4:10 pm
- Forum: New Software Releases
- Topic: 1.2.0.64
- Replies: 0
- Views: 6039
1.2.0.64
Fixed – KICKR calibration did not work in few cases after update.
- Sun Mar 30, 2014 4:05 pm
- Forum: Software Support
- Topic: "Error message" pops up upon program start after update
- Replies: 2
- Views: 6562
Re: "Error message" pops up upon program start after update
OK that fixes the error dialog on update issue. Kickr Calibration no longer works Well it works but not always. This was because I followed an advise from Wahoo not to send messages to KICKR more often then once every 2 seconds. I finally followed it and hence the result. Calibration part of KICKR ...
- Sun Mar 30, 2014 2:20 pm
- Forum: Software Support
- Topic: Kickr Droputs
- Replies: 6
- Views: 13363
Re: Kickr Droputs
Ok it is definitely not your system. Back to KICKR drops They have bug (they've acknowledged it) in their firmware that causes connection loss when operating over ANT+. Some affected by it and some not. Bug does not express itself all the time so I guess it is difficult to catch. However I have cust...